MPS Industries, Inc. - R3600 Series Wideband Isolation Transformers

For RF, DS3/E3, Broadband, BPL and Ethernet Magnetics which require Supplementary or Reinforced Isolation
Construction complies with IEC60950 Isolation requirements

Request Information Sample or Quote Request

Unit of Measure

Items	R3600-1 500 Microhenry (µH) Minimum Inductance (1-4) R3600 Series Wideband Isolation Transformer	R3600-2 800 Microhenry (µH) Minimum Inductance (1-4) R3600 Series Wideband Isolation Transformer	R3600-3 120 Microhenry (µH) Minimum Inductance (1-4) R3600 Series Wideband Isolation Transformer	R3600-4 120 Microhenry (µH) Minimum Inductance (1-4) R3600 Series Wideband Isolation Transformer	R3600-5 200 Microhenry (µH) Minimum Inductance (1-4) R3600 Series Wideband Isolation Transformer
Turns Ratio (Primary : Secondary) (±5 %)	N/A 1:1	N/A 1CT:1CT	N/A 1:2	N/A 1:1:1	N/A 3:3:1
Minimum Inductance (1-4)	N/A 500 µH	N/A 800 µH	N/A 120 µH	N/A 120 µH	N/A 200 µH
Maximum Direct Current Resistance (DCR) (1-4)	N/A 0.30 Ohm	N/A 0.50 Ohm	N/A 0.20 Ohm	N/A 0.20 Ohm	N/A 0.30 Ohm
Maximum Insertion Loss (1 MHz)	N/A -0.5 dB	N/A -0.5 dB	N/A -0.8 dB	N/A -0.8 dB	N/A -0.5 dB
Maximum Insertion Loss (100 MHz)	N/A -1.0 dB	N/A -1.2 dB	N/A -1.0 dB	N/A -1.0 dB	N/A -1.0 dB
Typical Insertion Loss (300 MHz)	N/A -2.6 dB	N/A -3.5 dB	N/A -1.5 dB	N/A -1.5 dB	N/A -3.0 dB
Hipot (Primary to Secondary)	N/A 4500 Vrms	N/A 3000 Vrms	N/A 4500 Vrms	N/A 4500 Vrms	N/A 3000 Vrms
Schematic	N/A B	N/A A	N/A B	N/A C	N/A C
Standard Operating Temperature Range¹	N/A 0 to +70 ºC
Available Impedance Data	N/A 50 Ohm75 Ohm
Industry Standards / Certifications	N/A IEC60950 RoHS Compliant
Available Design	N/A custom
Note	N/A OCL measured @ 100 kHz, 0.1 Vrms at Pin 1-4 (with 2-3 shorted) Insertion Loss measured with 100 ohm as Input (Primary) Impedance between 1-4 and Output (Secondary) load with respective impedance 50 Ohm and 75 Ohm impedance data available upon request Product performance is limited to specified parameters. Data is subject to change without prior notice. Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X.X : ±0.38 X.XX : ±0.10
¹ Extended operating temperature available upon request.